Waterworks Henry One Hole Bar Faucet , Metal Cross Handle Manual do Utilizador descarregar pdf

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST

HENRY

One Hole Bar Faucet with Metal Cross Handle

Installation Guidelines

Page 1 of 2

Rev

10.16.2014

These guidelines have been prepared for the professional contractor to aid in the installation of:

HENRY ONE HOLE BAR FAUCET WITH METAL CROSS HANDLE (STYLE No. HNKM40, HN40KM UK).

All dimensions are based on original specification and are subject to change and variation.

Please consult your Design Associate for current specifications.

STYLE No. HNKM40†

SPECIFICATIONS

Deck Thickness Maximum: 1-1/4” (32mm)

Fittings Hole Diameter: Ø1-3/8” (35mm)

Handle Turn Angle: Half Turn

Inlet Connection Size: 3/8”

Inlet Connection Type: Compression Connection Hoses†

Restricted Maximum Flow Rate: 2.2gpm (8.3liters/min)

Spout Reach: 5-1/4” (133mm)

Spout Swivel: No

Water Pressure Minimum: 20 psi (1.4 Bar)

Water Pressure Maximum: 80 psi (5.5 Bar)

Water Pressure Recommended: 45 psi (3 Bar)

† UK Style No. HN40KM is supplied with 2 BSP adapters,

assembly required.

IMPORTANT:

¾ To ensure this product is installed properly, you must

read and follow these guidelines.

¾ The owner/user of this product must keep this

information for future reference..

¾ This product must be installed by a professional

licensed contractor.

¾ Be sure your installation conforms to all federal, state,

and local codes.

¾ In the State of Massachusetts, all installations must

comply with the rules and regulations set forth within

248 CMR.

¾ Refer to the specification and assembly drawings

attached. Product is sold partially assembled but

shown fully disassembled for illustrative and service

purposes only.

¾ Inspect the product to ensure you have all the parts

required for proper installation.

¾ Use only a strap wrench or protected/smooth-jaw

wrench on any finished surface.

¾ DO NOT use putty. Putty contains oil and can cause

permanent discoloration on certain materials such as

marble, granite and any porous surface.

¾ NOTE: The screw on the top of the handle is purely

aesthetic. DO NOT REMOVE.

INSTALLATION

1. Remove the NUTS, METAL WASHER, and UPPER

RUBBER WASHER from the THREADED RODS. See

FIGURE - 01.

NUTS

SPOUT

ASSEMBLY

AERATOR

REMOVAL

KEY

METAL

WASHER

LOWER

RUBBER

WASHER

INLET

SUPPLY

HOSES

THREADED

RODS

UPPER

RUBBER

WASHER

FLOW

RESTRICTING

AERATOR

NUTS

SPOUT

ASSEMBLY

AERATOR

REMOVAL

KEY

METAL

WASHER

LOWER

RUBBER

WASHER

INLET

SUPPLY

HOSES

THREADED

RODS

UPPER

RUBBER

WASHER

FLOW

RESTRICTING

AERATOR

FIGURE – 01

2. Ensure that the INLET SUPPLY HOSES and

THREADED ROD are securely tightened to the SPOUT

ASSEMBLY, then insert the HOSES and THREADED

RODS through the Ø1-3/8” (35mm) hole on the

mounting surface making sure the UPPER RUBBER

WASHER is beneath.

1 2

Installation Guidelines 1

Resumo do Conteúdo

Página 1 - Installation Guidelines

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST HENRY One Hole Bar Faucet with Metal Cross Handle Installation Guidelines Page 1 of 2Rev - 01 10.16.20

Página 2

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST HENRY One Hole Bar Faucet with Metal Cross Handle Installation Guidelines Page 2 of 2Rev - 01 10.16.20

Comentários a estes Manuais

Sem comentários

Waterworks Henry One Hole Bar Faucet , Metal Cross Handle Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Acessórios para água Waterworks Henry One Hole Bar Faucet , Metal Cross Handle. Waterworks Henry One Hole Bar Faucet , Metal Cross Handle User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Acessórios para água Waterworks Henry One Hole Bar Faucet , Metal Cross Handle