Waterworks .25 Deck Mounted Low Profile Concealed Tub Filler Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Acessórios para água Waterworks .25 Deck Mounted Low Profile Concealed Tub Filler . Waterworks .25 Deck Mounted Low Profile Concealed Tub Filler with Handshower and Metal Cross Handles User Manual Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 2
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
1
2
4
5
6
7
3
8
9
3"
9"
4
7
/8"
Ø
2
3
/8"
2
3
/16"
Ø
2
3
/8"
.25
®
Concealed Tub Filler With Cross Handle
1/05
WATERWORKS
®
These guidelines have been prepared for the professional contractor to aid in the installation of:
.25 CONCEALED TUB FILLER WITH CROSS HANDLE (PTTU43-K)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
Figure 1
1
Refer to the specification and assembly drawings
attached. Faucet is sold partially assembled but shown
fully disassembled for illustrative and service purposes
only.
Inspect this product to assure you have all parts
required for proper installation.
Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
Install accessible hot and cold service stop valves to
facilitate servicing.
Do NOT use putty during this installation.
ROUGH-IN:
1. Run well supported ¾" hot and cold supply lines for
maximum water flow. 1 3/8" drilling for the mounting
holes is recommended.
SIDE VALVE INSTALLATION:
2. Remove the handle trim connector(2), gasket(3) and
plastic spacer(4) from the side valve(8). Do not
remove the lock nut(9), washer(6), and lower gasket(5).
3. Determine the thickness of the mounting surface. If it
is less than 1 ½", slide the plastic spacer(4) onto the
side valve. If the surface is greater than 1 ½", do not
use the spacer.
4. Insert the side valve(5-9) into the hole in the mounting
surface.
5. Thread the handle trim connector(2) completely onto
the side valve (about 6 full turns) until it stops. If the
connector does not thread down completely, adjust the
lock nut.
6. After the connector is on completely, tighten the lock
nut against the underside of the mounting surface to
secure the side valve.
7. Position the handle assembly(1) over the valve then
thread the handle assembly onto the side valve until it
stops. Hand tight is adequate; if this assembly is too
tight, the handle will bind.
8. Repeat these steps to install the second side valve.
PTTU43-K
IMPORTANT:
TToo eennssuurree tthhiiss pprroodduucctt iiss iinnssttaalllleedd pprrooppeerrllyy,, yyoouu mmuusstt rreeaadd
aanndd ffoollllooww tthheessee gguuiiddeelliinneess..
TThhee oowwnneerr//uusseerr ooff tthhee ffaauucceett mmuusstt kkeeeepp tthhiiss iinnffoorrmmaattiioonn
ffoorr ffuuttuurree rreeffeerreennccee..
Be sure your installation conforms to local codes. Anti
scald protection is the responsibility of the installer and
according to applicable codes.
This tub filler should be on-site prior to rough in and allows
the installer to visualize the installation.
An access panel must be installed for servicing and
installation.
Check tub deck and tub measurements to assure the
spout projects far enough into the tub.
Vista de página 0
1 2

Resumo do Conteúdo

Página 1 - Installation Guidelines

1245673893"9"47/8"Ø23/8"23/16"Ø23/8".25®Concealed Tub Filler With Cross Handle1/05WATERWORKS®These guidelines have been

Página 2

.25®Concealed Tub Filler With Cross Handle1/05WATERWORKS®These guidelines have been prepared for the professional contractor to aid in the installatio

Comentários a estes Manuais

Sem comentários